Idle State
Once you have handled all the previously covered requests the device should be enumerated and remain idle awaiting for a new host request. Your logs may look like this:
INFO:usb_4 -- USB: UsbReset @ 318.66455ms
INFO:usb_4 -- USB reset condition detected
INFO:usb_4 -- USB: UsbEp0Setup @ 391.418456ms
INFO:usb_4 -- EP0: GetDescriptor { descriptor: Device, length: 64 }
INFO:dk::usbd -- EP0IN: start 18B transfer
INFO:usb_4 -- USB: UsbEp0DataDone @ 391.723632ms
INFO:usb_4 -- EP0IN: transfer complete
INFO:dk::usbd -- EP0IN: transfer done
INFO:usb_4 -- USB: UsbReset @ 442.016601ms
INFO:usb_4 -- USB reset condition detected
INFO:usb_4 -- USB: UsbEp0Setup @ 514.709471ms
INFO:usb_4 -- EP0: SetAddress { address: Some(17) }
INFO:usb_4 -- USB: UsbEp0Setup @ 531.37207ms
INFO:usb_4 -- EP0: GetDescriptor { descriptor: Device, length: 18 }
INFO:dk::usbd -- EP0IN: start 18B transfer
INFO:usb_4 -- USB: UsbEp0DataDone @ 531.646727ms
INFO:usb_4 -- EP0IN: transfer complete
INFO:dk::usbd -- EP0IN: transfer done
INFO:usb_4 -- USB: UsbEp0Setup @ 531.829832ms
INFO:usb_4 -- EP0: GetDescriptor { descriptor: DeviceQualifier, length: 10 }
ERROR:usb_4 -- EP0IN: unexpected request; stalling the endpoint
INFO:usb_4 -- USB: UsbEp0Setup @ 532.226562ms
INFO:usb_4 -- EP0: GetDescriptor { descriptor: DeviceQualifier, length: 10 }
ERROR:usb_4 -- EP0IN: unexpected request; stalling the endpoint
INFO:usb_4 -- USB: UsbEp0Setup @ 532.592772ms
INFO:usb_4 -- EP0: GetDescriptor { descriptor: DeviceQualifier, length: 10 }
ERROR:usb_4 -- EP0IN: unexpected request; stalling the endpoint
INFO:usb_4 -- USB: UsbEp0Setup @ 533.020018ms
INFO:usb_4 -- EP0: GetDescriptor { descriptor: Configuration { index: 0 }, length: 9 }
INFO:dk::usbd -- EP0IN: start 9B transfer
INFO:usb_4 -- USB: UsbEp0DataDone @ 533.386228ms
INFO:usb_4 -- EP0IN: transfer complete
INFO:dk::usbd -- EP0IN: transfer done
INFO:usb_4 -- USB: UsbEp0Setup @ 533.569335ms
INFO:usb_4 -- EP0: GetDescriptor { descriptor: Configuration { index: 0 }, length: 18 }
INFO:dk::usbd -- EP0IN: start 18B transfer
INFO:usb_4 -- USB: UsbEp0DataDone @ 533.935546ms
INFO:usb_4 -- EP0IN: transfer complete
INFO:dk::usbd -- EP0IN: transfer done
INFO:usb_4 -- USB: UsbEp0Setup @ 534.118651ms
INFO:usb_4 -- EP0: SetConfiguration { value: Some(42) }
ERROR:usb_4 -- EP0IN: unexpected request; stalling the endpoint
Note that these logs are from a Linux host where a SET_CONFIGURATION request is sent after the SET_ADDRESS request. On other OSes you may not get that request before the bus goes idle. Also note that there are some GET_DESCRIPTOR DeviceQualifier requests in this case; you do not need to parse them in the usb crate as they'll be rejected (stalled) anyways.
You can find traces for other OSes in these files (they are in the advanced folder):
linux-enumeration.txt(same logs as the ones shown above)macos-enumeration.txtwin-enumeration.txt
✅ Double check that the enumeration works by running cargo xtask usb-list while usb-4.rs is running.
Bus 001 Device 013: ID 1366:1015 <- J-Link on the nRF52840 Development Kit
(..)
Bus 001 Device 016: ID 2020:0717 <- nRF52840 on the nRF52840 Development Kit
Both the J-Link and the nRF52840 should appear in the list.
You can find a working solution up to this point in src/bin/usb-4-solution.rs. Note that the solution uses the usb2 crate to parse SETUP packets and that crate supports parsing all standard requests.